Rab11 Pull-Down Activation Assay Kit
Cat. # 83201
Introduction
A. Background
Small GTPases are a super-family of cellular ing regulators. Rab11 has been shown to control traffic through the recycling endosome.
The Rab11 Activation Assay Kit is based on the configuration-specific monoclonal antibody that specifically recognizes Rab11-GTP, but not Rab11-GDP. Given the high affinity of monoclonal antibodies to their antigens, the activation assay could be performed in a short time. This assay provides the reliable results with consistent reproducibility.
Currently there is no direct assay to measure the activation of Rab11 GTPases.
B. Assay Principle
The Rab11 Activation Assay Kit uses configuration-specific anti-Rab11-GTP Mouse monoclonal antibody to measure Rab11-GTP levels in cell extracts or in vitro GTPγS loading Rab11 activation assays. Anti-Rab11-GTP mouse monoclonal antibody is first incubated with cell lysates containing Rab11-GTP. Next, the GTP-bound Rab11 is pulled down by protein A/G agarose. Finally, the precipitated Rab11-GTP is detected through immunoblot analysis using Anti-Rab11 Rabbit Polyclonal Antibody.
C. Kit Components
1. Anti-Rab11-GTP Mouse Monoclonal Antibody (Cat. # 26919): One vial – 35 µL (1 mg/ml) in PBS, pH 7.4, containing 50% glycerol. This antibody specifically recognizes Rab11-GTP from all vertebrates.
2. Protein A/G Agarose (Cat. # 30301): One vial – 600 µL of 50% slurry.
3. 5X Assay/Lysis Buffer (Cat. # 30302): One bottle – 30 mL of 250 mM Tris-HCl, pH 8, 750 mM l, 50 mM MgCl2, 5 mM EDTA, 5% Triton X-100.
4. Anti-Rab11 Rabbit Polyclonal Antibody (Cat. # 21157): One vial – 50 µL (1 mg/mL) in PBS, pH 7.4, contained 50% glycerol.
5. 100X GTPγS (Cat. # 30303): One vial – 50 µl at 10 mM, use 5 µL of GTPγS for GTP-labeling of 0.5 mL of cell lysate.
6. 100X GDP (Cat. # 30304): One vial – 50 µl at 100 mM, use 5 µL of GDP for GDP-labeling of 0.5 mL of cell lysate.
7. HRP-Goat Anti-Rabbit IgG (Cat. #29002): 50 µL (0.4 mg/mL) in PBS, pH 7.4, contained 50% glycerol.
D. Materials Needed but Not Supplied
1. Stimulated and non-stimulated cell lysates
2. Protease inhibitors
3. 4 °C tube rocker or shaker
4. 0.5 M EDTA at pH 8.0
5. 1.0 M MgCl2
6. 2X reducing SDS-PAGE sample buffer
7. Electrophoresis and immunoblotting systems
8. Immunoblotting wash buffer such as TBST (10 mM Tris-HCl, pH 7.4, 0.15 M l, 0.05% Tween-20)
9. Immunoblotting blocking buffer (TBST containing 5% Non-fat Dry Milk or 3% BSA)
10. ECL Detection Reagents
E. Example Results
The following figure demonstrates example results seen with the Rab11 Activation Assay Kit. For reference only.
Rab11 Activation Assay.Purified Rab11 proteins were immunoprecipitated after treated with GDP (lane 1) or GTPγS (lane 2). Immunoprecipitation was done with the anti-Rab11-GTP monoclonal antibody (Cat. # 26919). Immunoblot was with an anti-Rab11 polyclonal antibody (Cat. # 21157).Assay Procedure
A. Reagent Preparation
1X Assay/Lysis Buffer: Mix the 5X Stock (Cat. # 30301) briefly and dilute to 1X in deionized water. Just prior to usage, add protease inhibitors such as 1 mM PMSF, 10 µg/mL leupeptin, or 10 µg/mL aprotinin.B. Sample Preparation
Adherent Cells
1. Culture cells (one 10-cm plate, ~107 cells) to approximately 80- confluence. Stimulate the cells with activator or inhibitor as desired.
2. Aspirate the culture media and wash twice with ice-cold PBS.
3. Completely remove the final PBS wash and add ice-cold 1X Assay/Lysis Buffer (See Reagent Preparation) to the cells (0.5-1 mL per 10 cm tissue culture plate).
4. Place the culture plates on ice for 10-20 minutes.
5. Detach the cells from the plates by scraping with a cell scraper.
6. Transfer the lysates to appropriate size tubes and place on ice.
7. If nuclear lysis occurs, the cell lysates may become viscous and difficult to pipette. If this occurs, lysates can be passed through a 27½-gauge syringe needle 3-4 times to shear the genomic DNA.
8. Clear the lysates by centrifuging at 12,000 x g and 4°C for 10 minutes.
9. Collect the supernatant and store the sample (~1-2 mg of total protein) on ice for immediate use, or snap freeze and store at -70°C for future use.
Adherent Cells
1. Culture cells and stimulate with activator or inhibitor as desired.
2. Perform a cell count and then pellet the cells through centrifugation.
3. Aspirate the culture media and wash twice with ice-cold PBS.
4. Completely remove the final PBS wash and add ice-cold 1X Assay/Lysis Buffer (See Reagent Preparation) to the cell pellet (0.5-1 mL per 107 cells).
5. Lyse the cells by repeated pipetting.
6. Transfer the lysates to appropriate size tubes and place them on ice.
7. If nuclear lysis occurs, the cell lysates may become viscous and difficult to pipette. If this occurs, lysates can be passed through a 27½-gauge syringe needle 3-4 times to shear the genomic DNA.
8. Clear the lysates by centrifuging at 12,000 x g and 4°C for 10 minutes.
9. Collect the supernatant and store sample on ice for immediate use, or snap freeze and store at -70°C for future use.
C. In vitro GTPγS/GDP Protein for Positive and Negative controls
Note: In vivo stimulation of cells will activate approximately 10% of the available Rab11, whereas in vitro GTPγS protein loading will activate nearly of Rab11.
1. Aliquot 0.5 mL of cell extract (or 1 µg of purified Rab11 protein) into two microcentrifuge tubes.
2. To each tube, add 20 µL of 0.5 M EDTA (final concentration of 20 mM).
3. Positive control: add 5 µL of 100 X GTPγS (Cat. # 30302) to the 1st tube
4. Negative control: add 5 µL of 100 X GDP (Cat. # 30304) to the 2nd tube.
5. Incubate both tubes at 30°C for 30 minutes with agitation.
6. Stop loading by placing the tubes on ice and adding 32.5 µL of 1 M MgCl2 (final concentration of 60 mM).
D. Affinity Precipitation of Activated G Protein
1. Aliquot 0.5-1 mL of cell lysates (about 1 mg of total cellular protein) to a microcentrifuge tube.
2. Adjust the volume to 1 mL with 1X Assay/Lysis Buffer (See Reagent Preparation).
3. Add 1 µL anti-Rab11-GTP antibody (Cat. # 26919).
4. Prepare the protein A/G Agarose bead slurry (Cat. # 30301) by resuspending through vertexing or titrating.
5. Quickly add 20 µL of resuspended bead slurry to above tube.
6. Incubate the tube at 4°C for 1 hour with gentle agitation.
7. Pellet the beads through centrifugation at 5,000 x g for 1 min.
8. Aspirate and discard the supernatant (making sure not to disturb or remove the bead pellet.
9. Wash the beads 3 times with 0.5 mL of 1X Assay/Lysis Buffer, centrifuging and aspirating each time.
10. After the third wash, pellet the beads through centrifugation and carefully remove all the supernatant.
11. Resuspend the bead pellet in 20 µL of 2X reducing SDS- PAGE sample buffer.
12. Boil the sample for 5 minutes.
13. Centrifuge it at 5,000 x g for 10 seconds.
E. Western Blot Analysis
1. Load 15 µL/well of pull-down supernatant to a polyacrylamide gel (17%). It is recommended to include a pre-stained MW standard (as an indicator of a successful transfer in step 3 below).
2. Perform SDS-PAGE following the manufacturer’s instructions.
3. Transfer the gel proteins to a PVDF or nitrocellulose membrane following the manufacturer’s instructions.
Note: Steps 4-11 are at room temperature with agitation
4. Following electroblotting, immerse the PVDF membrane in ** Methanol for 15 seconds, and then allow it to dry at room temperature for 5 minutes.
Note: If Nitrocellulose is used instead of PVDF, step 4 Should be skipped.
5. Block the membrane with 5% non-fat dry milk or 3% BSA in TBST for 1 hr at room temperature with constant agitation.
6. Wash the blotted membrane three times with TBST, 5 minutes each time.
7. Incubate the membrane with Anti-Rab11 Rabbit Polyclonal Antibody (Cat. # 21157), which is freshly diluted 1: 50~500 (depending on the amount of Rab11 proteins in your sample) in 5% non-fat dry milk or 3% BSA in TBST, for 1-2 hr at room temperature with constant agitation or at 4°C overnight.
8. Wash the blotted membrane three times with TBST, 5 minutes each time.
9. Incubate the membrane with a secondary antibody (Cat. # 29002), which is freshly diluted 1: 1000 in 5% non-fat dry milk or 3% BSA in TBST, for 1 hr at room temperature with constant agitation.
10. Wash the blotted membrane three times with TBST, 5 minutes each time.
11. Use the detection method of your choice such as ECL.
武汉费斯德生物科技有限公司是美国NewEast Biosciences在中国的办事处，也是目前国内经销处。
目前客户使用产品发表**过1000谷歌学术文献，其中论文分布排名前50刊物上。
NewEast Biosciences 在十二年前研发俩种*特的抗体。这俩种抗体仅仅识别活性的GTP酶或者突变的Oncogene。 GTP酶涉及(1)响应细胞表面受体的信号转导，包括跨膜受体，例如介导味觉、嗅觉和视觉的那些，（2）核糖体的蛋白质生物合成，（3）调节细胞分化、增殖、分裂和运动，（4）蛋白质通过膜的易位，（5）细胞内囊泡的运输，以及囊泡介导的分泌和摄取，通过GTP酶控制囊泡外壳组装。Oncogene侧是诱发癌症的基因。
更多产品类目和技术资料可查看：武汉费斯德生物官网。
武汉费斯德生物科技有限公司将向你提供以下，抗体或者试剂盒: (1) 仅识别 GTP酶的活性构型的产品, 它可以让你能够量化GTP酶在细胞中的活性和分布。(2) 识别突变 Oncogene蛋白, 但不认识相应**型的抗体。 (3) 对 cAMP 和 cGMP 具有**亲和力（*乙酰化）ELISA检测试剂盒。
注：2021年武汉费斯德生物科技有限公司和NewEast Biosciences收购了武汉纽斯特生物技术有限公司所有的产品和细胞株。因此, 纽斯特不再拥有这些产品销售权。如果您在 2022 年 6 月 1 日之后从 纽斯特购买相同的产品, 你不应该在你的论文中引用 纽斯特的产品为NewEast Biosciences产品。 否则，NewEast Biosciences 会去找出版商对你的引用提出异议。请注意, 用国际供应商的产品将会增加您发表文章citation的数量。
选择正品费斯德经销处，为您实验和相关文章提供**，售后服务到位，产品现货供应。
** 本公司销售的所有产品仅供实验科研使用，不用于人体及临床诊断。
http://neweastbio.b2b168.com
欢迎来到武汉费斯德生物科技有限公司网站， 具体地址是湖北省武汉市洪山区东湖新技术开发区高新大道666号武汉国家生物产业基地项目（生物创新园）B.C.D区研发楼B3-3栋3楼，联系人是付女士。
主要经营GTP酶和癌基因产品，Rac GTP antigody,武汉活性抗体现货集采，active RAC antibody,Rac GTP 小鼠单抗， Anti-Rac1-GTP Monoclonal Antibody,Cdc42 GTP antibody,BRAF(V600E) 小鼠单抗，Rap1 pull down activation assay kit,Rheb 活性检测试剂盒。。
单位注册资金未知。
公司长期供应G蛋白活性抗体及试剂盒,非乙酰化CAMP和CGMP试剂,点突变抗体等，产品质量完全符合行业要求，被用户评为信得过产品，**全国各省市、自治，欢迎新老客户来选购考察！
3
